Exhibitor products

Ethernet participants, such as PLC control systems, can be reached with the REX 100 industrial routers, irrespective of the manufacturer. Following models are available: - REX 100 WiFi, 3 x LAN (switch)/1 x WAN/1 x WiFi interface - REX 100 3G, 4 x LAN (switch)/1 x 3G modem (UMTS) - REX 100 LTE, 4 x LAN (switch)/1 x LTE modem (EU- & Asia-Version) - REX 100 LTE, 3 x LAN (switch)/1 x WAN/1 x LTE-Modem (EU- & Asia-Version) - REX 100 LTE, 4 x LAN (switch)/1 x LTE modem (North America Version / “NAG“) - REX 100 WiFi, 4 x LAN (switch)/1 x WiFi interface - REX 100 WiFi, 3 x LAN (switch)/1 x WAN/1 x WiFi interface The REX 100 routers are systematically designed to operate in conjunction with the myREX24 V2 portal: All programming and remote maintenance is carried out exclusively through the portal. With the digital inputs, alarms can be sent via the myREX24 V2 portal as SMS and e-mail. The USB host port present in all devices enables the connection of USB devices (e.g. programming port of a drive) via the remote maintenance tunnel (USB-over-IP). The REX 100 WiFi establishes the connection with the myREX 24 V2 portal via WLAN. Additional Ethernet participants can be connected at the router via the integrated 3-port switch. For data transmission, our industrial router uses an encrypted VPN tunnel on the basis of the secure OpenVPN protocol.

With the REX 200 industrial routers, Ethernet subscribers, such as PLC controllers, can be achieved regardless of manufacturer. Following models are available: - REX 200 WAN, 4 x LAN (switch)/1 x WAN port - REX 200 LTE, 4 x LAN (switch)/1 x WAN/1 x LTE modem - REX 200 WiFi, 4 x LAN (Switch)/1 x WAN/1 x WiFi interface The REX 200 routers are designed for operation in conjunction with the myREX24 V2 portal: The complete parameterization and remote maintenance is carried out via the portal. In addition to remote maintenance, the REX 200 routers can also read data from the PLC, visualize and generate alarms. For remote maintenance and data transmission, the industrial router uses an encrypted VPN tunnel based on the secure OpenVPN protocol. With the 4 digital inputs, alarms can be sent via SMS and email via the myREX24 V2 Portal. The 2 digital outputs can be system states of the router, e.g. with a lamp on the control cabinet, or can be activated via the portal. The USB host interface available on all devices enables the connection of USB device devices (eg programming interface of a drive) via the remote maintenance tunnel (USB-over-IP). The REX 200 WiFi establishes the connection to the myREX 24 V2 portal via WLAN. Additional Ethernet devices can be connected to the router via the integrated 4-port switch. For data transmission, our industrial router uses an encrypted VPN tunnel based on the secure OpenVPN protocol.

With the REX 250 industrial routers, Ethernet subscribers, such as PLC controllers, can be achieved regardless of manufacturer. Following models are available: REX 250 WAN, 4 x LAN (switch)/1 x WAN interface REX 250 3G, 4 x LAN (switch)/1 x WAN/1 x 3G modem (UMTS) REX 250 LTE, 4 x LAN (switch)/1 x WAN/1 x LTE modem The REX 250 routers are designed for operation in conjunction with the myREX24 V2 portal: The complete parameterization and remote maintenance is carried out via the portal. In addition to remote maintenance, the REX 250 routers can also read data from the PLC, visualize and generate alarms. For remote maintenance and data transmission, the industrial router uses an encrypted VPN tunnel based on the secure OpenVPN protocol. The REX 250 routers also enable remote maintenance and data access to PLCs via an MPI / PROFIBUS and via an RS232 interface. With the 4 digital inputs, alarms can be sent via SMS and email via the myREX24 V2 Portal. The 2 digital outputs can change the system states of the router, e.g. with a lamp on the control cabinet, or can be activated via the portal. The USB host interface available on all devices enables the connection of USB device devices (eg programming interface of a drive) via the remote maintenance tunnel (USB-over-IP). The REX 250 WiFi establishes the connection to the myREX 24 V2 portal via WLAN. Additional Ethernet devices can be connected to the router via the integrated 4-port switch. For data transmission, our industrial router uses an encrypted VPN tunnel based on the secure OpenVPN protocol. REX 250 WiFi, 4 x LAN (Switch)/1 x WAN/1 x WiFi interface

With the compact or modular RFID system from TURCK, you can use the proven HF technology and the wide-reaching UHF technology in parallel in one identification solution. The TURCK RFID system offers data carriers, read/write heads, connectivity solutions and the corresponding interfaces, which can be flexibly combined depending on requirements. Interfaces are available for OPC UA, PROFINET, EtherNet/IP™, Modbus TCP, TCP/IP, PROFIBUS-DP, DeviceNet™, CANopen and EtherCAT®. Product groups - Identification systems by means of radio frequency and transponders (RFID) - Identification systems and coding systems by means of radio frequency (high-frequency signals) and transponders (RFID) - RFID transponders and transponder readers for mobile automation

Do you know the problem? Conventional labels on metal housings are often hard to recognize, or the serial number isn’t readily available when needed. As a result, users in service or troubleshooting situations often cannot contact the manufacturer right away because the required number is missing. In addition, standard RFID tags cannot be read on metallic surfaces. Similarly, QR codes can lose their readability due to wear, dirt, or scratches. With the AIXONTEC GmbH RFID Anti-Metal Labels (16 × 20 mm), these issues are a thing of the past. The label can be applied directly to metal housings and enables the storage of serial numbers as well as additional data, which can be reliably read using a smartphone or #NFC reader. The striking yellow color ensures high visibility and makes it easy to locate quickly. Thanks to its strong adhesive, the label remains securely in place even in demanding environments. On request, the serial number can also be printed directly on the label. ✅ Reliable performance on metal surfaces ✅ Rewritable NFC tag with up to 144 bytes or more ✅ Strong adhesion, even under harsh conditions ✅ Compact size (16 × 20 mm) with high visibility ✅ Optional printed serial number ✅ Operating temperature range: -35 °C to +85 °C

New possibilities for ST series safety sensors Pizzato Elettrica further expands its range of ST series RFID safety sensors with the introduction of the new ST H version. The ST H series RFID sensors are equipped with all the technical and operating features already available in the ST G series, including: M12 plastic or stainless steel connector; Multicolour signalling LED, visible from both sides of the housing; Multitag programming; Versions for wide temperature ranges from -35°C to +85°C. Magnetic holding of the actuator Devices of the ST H series can be configured with a permanent magnet incorporated inside the housing, able to generate a holding force between sensor and actuator. This way, the guard can be kept closed even where there are vibrations, after a recoil during closing, or in areas where air turbulence tends to open the lighter guards. The magnetic holding force can be selected among three different magnitudes, in order to adapt to any usage situation. Symmetrical housing, standard hole spacing The symmetry of the housing allows the same sensor to be used on both left and right doors; by simply rotating the sensor onto itself. The 78 mm mounting hole spacing facilitates the replacement of the traditional SR B magnetic sensors with an advanced RFID safety sensor. ADVANTAGES: All the already existing technology from the ST G series of sensors; User configurable magnetic holding force of the actuator; The symmetrical housing makes it easy to mount; Same mounting hole spacing (78 mm) as for SR B series devices; Compatible with all ST series actuators; The protection degrees IP67 and IP69K allow the use in the toughest conditions.

The RG2 - 2kg payload robot arm gripper is a flexible collaborative gripper with built-in Quick Changer up to 110mm stroke. It provides intelligence, fast deployment, easy customization and programming. The outstanding software features through our one system solution decreasing engineering and manufacturing time significantly. The RG2 gripper is a tool for wide range of applications. Customized fingertips provide great gripping flexibility, customers can use one tool for different parts of the production process maximizing robot utilization. The RG2 works seamlessly with our Dual Quick Changer and any of our other grippers to help you maximize utilization of your robots. RG2 is TÜV certified, comes standard with safety shields.

The RG6 – 6kg payload robot arm gripper is a flexible collaborative gripper with built-in Quick Changer, up to 150mm stroke. It provides intelligence, fast deployment, easy customization and programming. The outstanding software features that come with the product enable intelligent applications. The RG6 gripper is a tool for wide range of applications. Customized fingertips provide extensive gripping flexibility, customers can use one tool for different parts of the production process maximizing robot utilization. The RG6 works seamlessly with our Dual Quick Changer and any of our other grippers to help you maximize utilization of your robots. RG6 is TÜV certified, comes standard with safety shields.

It is made in the RONTRON-R-JUWEL design and includes a RGB-SMD LED. Besides the option to choose between 7 colours, the illumination uniformity and the depth of colour have become even more homogeneous and intense. The standard colours are white, red, green, blue, yellow, magenta and cyan, but it is possible to access the whole RGB colour range, using a PWM signal (pulse width modulation). The pilot light is easily connected via the SMD flat clamp, just inserting the cable. The clamp ensures the connection and keeps the cable in place. A safety diode protects the LED against damage in case of improper connection of the cable. The new RGB pilot light is made for 22.3 mm mounting holes and fulfils IP65, being dust and waterproof. It is designed for an operating voltage of 24V and a max. amperage of 50mA, having an operating temperature range of -30°C to 70°C.

Rigid couplings are small, compact power packs to transfer high torques at a minimum of available space. Shaft diameter: 5 – 104mm Torque range: 25 – 12500Nm

A new lightning fast platform for power distribution RiLineX from Rittal is a newly developed, open platform for power distribution systems. A click system of boards and components simplifies the previously laborious process of assembling power distribution systems in enclosures. The end result is a time saving of up to 30 percent in engineering and 50 percent in assembly compared to conventional busbar systems. A further advantage is that RiLineX boosts sustainability by reducing plastic waste and increasing decentralised supply opportunities, with fewer shipments of heavy copper required. The innovative solution has been declared a winner by the German Design Award 2025 for its product design.

All functions at a glance - Fast, plausibility-checked selection of enclosures and accessories - Simple planning of cut-outs and holes, including real-time visualisation of the configuration in 3D - Automatic generation of order and manufacturing data plus standard-compliant documentation - Configurations can be forwarded directly to EPLAN Pro Panel - Log onto the online shop for extended pricing information and order options Your benefits - Save time due to simple configuration and ordering process - No more errors when selecting accessories or machining options -Easier planning thanks to the instant product list and price display - Faster processes through integrated interfaces to Eplan and Rittal software

Our range of solutions, from manual tools through to fully automated machine technology, will significantly accelerate your processes.

Riveting technology refers to the production of secure and durable connections. With the aid of plastic deformation, the two (or more) materials are joined together with a positive fit. Our riveting technology is used in the automotive supply industry, the electrical industry, the aerospace industry, the lock and fittings industry, the furniture industry and the sports equipment and household appliance industry! Wobble riveting technology means the production of secure, durable and high-quality rivet joints. With the help of plastic deformation, the two (or more) materials are joined together with a positive fit. In contrast to other riveting techniques, the wobble riveting technique guides the riveting punch around the closing head, thus achieving a gentler treatment of the rivet surface. Due to our modular principle, each machine can be freely combined according to the application.

The METZ CONNECT field assembled RJ45 field plug pro is the right choice for structured cabling with industry or data centers with high data transmission rates up to 40 GBit/s where high-performance and reliable connections are needed. The RJ45 field plug pro is available in a 180° straight and 360° angled, 4-pair and 2-pair version. It can easily be connected to all common cable types without much preparation and its new design allows it to be used in restricted spaces. It impresses with its robust zinc die-cast housing and protected latch for industrial use. Its compact design makes the connector multi-port capable while being fully shielded. The RJ45 field plug pro is designed for field assembly without the need for special tools. It is suitable for Power over Ethernet (PoE, PoE plus, UPoE and 4PPoE), HDBaseT or other multimedia applications as well as for industry standards such as PROFINET and EtherNet/IP.