Exhibitor products

• For hygienic and industrial applications • For any conductive media, whether foaming, pasty or adhering - with conductivity > 5 µS/cm • Automated sensor adjustment to the media ensures high flexibility even in a large variety • Ideal for small measuring heights/tanks sized 200 mm to 3000 mm • Extremely short response time < 100 ms for highly dynamic processes • Digital IO-Link interface and additional Dual Channel

This compact and inexpensive power amplifier is designed to control proportional valves with a magnet. This amplifier in the connector housing is mounted directly on the valve. The device is designed for control and parameterization via I/O link and has a port Class B. The output current is regulated and therefore independent of the supply voltage and the magnet resistance. This module can be adapted to proportional valves from various manufacturers via the free parameterization of the power output stage. Typical applications: Current-controlled control of throttle or pressure valves as well as general inductive loads. Features • Power amplifier for proportional valves in a DIN EN 175 301-803 A connector housing • I/O – Link Port Class B, with internal galvanic isolation of the additional supply voltage • Complies with specification V1.1, data rate COM3 = 230.4 kBaud • Digital, reproducible settings • Can also be used as a soft switch amplifier (soft switching on and off) • M12 connector • Can be parameterized via I/O - Link • Free setting of ramps, MIN and MAX, dither (frequency, amplitude) and PWM frequency • Output current up to a maximum of 2.5 A, parameterizable • Adaptable to all standard proportional valves

The PM2 pinion is designed for gearboxes with a flange output shaft, and is equipped with a mechanical interface which is standardized in accordance with ISO 9409-1. Its small number of teeth allows high feed forces. The PM2 pinion for flange output shafts is mounted to the following gearbox series: PFHE, PSFN, PLFN and WPSFN

The PN/CAN gateway CANopen represents a full-featured CANopen master. As a master, the gateway supports network management, SYNC telegrams, nodeguarding/heartbeat for monitoring the nodes and LSS services. Up to 16 PDOs can be configured per CANopen slave. The parameterization of the CANopen nodes via SDO telegrams and the management of emergency messages is also possible. On the PROFINET network, the PN/CAN gateway is a PROFINET I/O device and supports transmission rates of up to 100 Mbit full duplex; on the CAN bus, up to 1 Mbit/s is supported. The I/O data of the CAN nodes are mapped transparently and freely configurable into the PROFINET network and can thus be processed directly in the PLC. The PN/CAN gateway is integrated into the hardware configurator with a GSDML file and can be fully configured there. Further software tools for parameterization, or handling blocks for programming, are not necessary, which makes the use of the gateway uncomplicated. The features MRP (media redundancy) as well as extensive diagnostic functions and an interface for online diagnostics complete the performance characteristics of the PN/CAN gateway.

With the PN/EtherNetIP Coupler, a simple and uncomplicated connection of a PROFINET machine to an EtherNet/IP machine is possible. The PN/EtherNetIP Coupler allows data transmission between a PROFINET controller and an EtherNet/IP PLC. Received input data on one side of the network are made available as output data on the other side of the network to the PLC. The I/O data exchange takes place live and as fast as possible without further handling blocks. The maximum size of the transferable I/O data is 1024 bytes. Up to 3 input and 3 output assemblies can be configured on the EtherNet/IP network side. Up to 300 slots are available for I/O modules. The integration into the PLC engineering tool is made possible by a GSDML file, an extra configuration software is not necessary. The configuration of the I/O data to be exchanged is performed in the Siemens engineering tool. An EDS file matching the configuration can then be downloaded from the website by the PN/EtherNetIP Coupler and used to configure the EtherNet/IP PLC.

The MQTT protocol has become established in recent years as a simple transmission protocol for messages in the IoT world. MQTT stands for "Message Queue Telemetry Transport Protocol" and is an OASIS standard. The MQTT protocol always uses a central broker for communication between devices, which receives messages from, for example, a sensor and forwards them to interested devices, such as a control unit. When a sensor sends data to the broker, it is called a "publish". If a device needs data, it must subscribe to the broker ("Subscribe"). The broker delivers the data to all subscribers when new data has arrived from the publisher. With the PN/MQTT Coupler it is possible to transfer values between a PROFINET machine (PLC) and a MQTT broker. It is possible to send values from the PLC via PROFINET to a broker ("Publish") as well as to subscribe values from a MQTT broker and receive them in the PLC via PROFINET ("Subscribe"). The integration into the PLC engineering tool is enabled by a GSDML file, an extra configuration software is not necessary. All settings for the MQTT connection can be done on the web page of the device. MQTT brokers can be connected locally in the own network ("On premise") as well as via the internet in the cloud. Direct integration into the PLC puts full control of the data exchange with the IoT world in the hands of the programmer.

Seamless data flow across networks. With the PN/PN Coupler, a simple and uncomplicated connection of two separate PROFINET networks is possible. The PN/PN Coupler enables data transmission between two PROFINET controllers. A PROFINET IO device is on both PROFINET network sides. Received input data on one of the network sides is made available as output data to the other network side. The IO data transfer takes place live and as quickly as possible without additional handling blocks. The maximum size of the transmitted IO data is 1024 bytes. Up to 16 slots for IO modules of 1 byte and up to 128 bytes are available. The incorporation into the PLC engineering tool is made possible by a GSDML file; special configuration software isn’t necessary.

Our customizable material utilizes resistance or capacitance to detect mechanical force, changing its conductivity in a compressed state. Made from medical grade polymers,it is engineered for stability and overload resistance. Flexibility delivered in 0,4mm sheets and customizable to various shapes and sizes. Adaptability for a wide range of applications from robotics and automation to wearables. Sensitivity at low forces and microns of compression with extended range capabilities. Durability to withstand harsh conditions while maintaining performance integrity.

Our specialized kit is ideal for engineers, technicians and research institutions who want to begin quickly and efficiently. Our kit is developed as a plug-n-play product with everything inlcuded to get started. Five Readouts can be used in parallel with the provided force sensors. Seamless Integration is provided with established communication protocols over USB and I2C. The LED Readout is equipped with range calibration buttons to be used for stand alone visualization. The compact Design facilitates easy installation with a form factor of only 60x35x16mm.

UNIMOTION PNCE electric cylinders are designed to provide advanced automation solutions with superior power and reliability.

✅ LSM-3 – our mini linear slide ✅ for the automation of small workpieces ✅ pneumatic driven ✅ 3 stroke lengths (20, 35 and 50 mm) ✅ with or without mounted shock absorbers ❗️2 guide carriages (sealed ball bearing guides) ❗️recommended payload of 0.5 kg is 5 times higher than the item weight ✅ hardened stop screws ✅ external stops ❗️ repeat accuracy +/-0.01 mm ✅ stop screws for stroke adjustment ❗️ stop screws are hollow = sensor holder. ✅ no additional interfering dimensions, installation space is used optimally ♻️ little air consumption as small workpieces to be moved ♻️ little installation space ❗️ matching mini gripper (PGM-29) ✅ can be mounted by grid e.g. at the front of the head of the linear unit Technical data LSM-3 ✅ Stroke lengths 20 mm, 35 mm, 50 mm ✅ lifting force 11 N, retraction force 7 N ✅ Max. payload 0.5 kg ✅ Repeat accurracy +/-0.01 mm ✅ Stroke adjustable on both sides 15 mm ✅ Guide: 2 guide carriages (sealed recirculating ball bearing guide) ✅ Weight 60-100 g depending on stroke length ✅ Option: with mounted hydraulic shock absorbers ✅ Centering system – e.g. B. to accommodate mini gripper PGM-29 Technical data parallel gripper PGM-29: ✅ Stroke per jaw 2 mm ✅ Repeat accurracy +/-0.02 mm ✅ Finger length max. 15 mm ✅ Clamping force at 6 bar: 16 N ✅ Recommended workpiece weight 0.13 kg (force-fitting) ✅ own weight 0.025 kg ✅ Query option via sensors

to stop one or more pallets (or workpieces) at a defined position • to damp impact energy for a gentle stopping of the pallet • to lower the stop plate to release pallet for further transportation • sensors to detect the exact position of the stop plate (depending on model, either integrated or optional accessory)

• to stop one or more pallets (or workpieces) at a defined position • to lower the stop plate to release pallet for further transportation • Sensors to detect the exact position of the stop plate (depending on model, either integrated or optional accessory)

Simple and uncomplicated connection of a PROFINET network with a ModbusTCP network is possible with the PN/ModbusTCP Coupler. The PN/ModbusTCP Coupler enables data transmission between a PROFINET controller and ModbusTCP participants. Received input data on one of the network sides is made available as output data to the other network side. The IO data transfer takes place live and as quickly as possible without additional handling blocks. The maximum size of the transmitted data is 1024 bytes input/output data. Up to 300 slots for I/O modules are available via which the PROFINET data can be connected to the ModbusTCP coils, inputs and registers as required. The full ModbusTCP address space of 65536 coils, inputs and registers is supported. The integration into the PLC engineering tool is made possible by a GSDML file. In addition to the PROFINET/ModbusTCP communication, the PN/ModbusTCP coupler also provides an MQTT publisher on both network sides. This means that the values ​​exchanged via the gateway can also be distributed to visualization or production data acquisition systems via MQTT.